AIRCRAFT MANUFACTURING EQUIPMENT

Link back to Home Page► www.centurymachinery.com

POINT and CLICK CATEGORIES or JUST SCROLL DOWN, CATEGORIES  ARE IN ALPHABETICAL ORDER.

*DEBURRING AND FINISHING MACHINES*
*ENGLISH WHEEL*
*PRESS, ELECTROSHAPE FLUID FORMING*
*PRESSES, FLUID FORMING BLADDER, Verson Wheelons*
*PRESSES, HYDROFORM,  Cincinnati*
*PROFILERS AND ROUTING MILLS*
*RIVETER AND DRILL*
*ROLLS, AIRCRAFT, Farnham*
*ROUTERS: Pin and Radial Type*
*SHRINKERS AND STRETCHERS, Kick and Pneumatic Type,
Manufactured by Erco and Marchant*
*STRETCH WRAP FORMING MACHINES Cyril Bath AND Hufford*
*STRUT GRINDER CNC, Butler Newall
CYLINDRICAL GRINDER, GAP BED*
*SWAGER, Tube and Solid, Hydroformer, Finn*
*WATER JET CUTTING SYSTEM, CNC* Scroll down hyperlink not working
*MISCELLANEOUS*      We can offer a full range of:
    Aircraft and Airport Ground Support Equipment
*AIRCRAFT PUSH PULL BACK TRACTOR*

If you require a Quote Sheet, PLEASE  send  us your requirements to:
CENTURY MACHINERY COMPANY INC.
1937 South Santa Fe Avenue
Los Angeles, California 90021

Email:  sales@centurymachinery.com

Website: www.centurymachinery.com
Telephone 1-213-627-2847
Fax 1-213-627-2499
 

DEBURRING AND FINISHING MACHINES

"THIS SANDER / GRINDER USED TO SAND EXOTIC METALS"
▼                      ▼
8" wide SIERRA TILTING BELT SANDER,    Model TBG58107C
    Sanding and Polishing Belt Power Tilt  thru 30 degrees forward and back.
    Work Area 20" x 33½"
    Drive motor 5 hp
Equipped with: Polishing Head.
    Dust Hop Refrigerated Dust Collector   Inventory Reference S0403-6305   

WET TYPE
▼
ACME VERTICAL WET BELT GRINDER / SANDER
Model BG8A
Sanding Belt: Width 8 inch x 108" Length
Bed 12" F-B x 17" L-R
Equipped with: Pneumatic Belt Tension.
    Belt Motor Drive 7½ hp
    Coolant Pump ½ hp
Reference G3975-9333
      Photos of unit prior to being painted.
This photo is not unit, use as example of finish.



WET TYPE
▼
27" AEM (Now Timesaver) RECIPROCATING BED ABRASIVE BELT GRINDER
Wide Belt,    EXTRA HEAVY DUTY      WET TYPE
Model 75-25          Date Mfg. 3-15-90
27" wide Sanding Belt
Reciprocating Bed, overall size  26" F-B x 28" L-R
Part Fixture Table 25" x 25" with 3 point clamping
Belt Motor Drive 75 hp
Automatic Reciprocating Bed movement, Longitudinally and Up Feed
Coolant Tank and Pump
Equipped with: Bed Positioning DRO.     Manual and Automatic Operation.
     Automatic Feed Cycle.    Fixture Clamping.   Operator Control Station.
     Drive Motor per cent load meter.    Coolant Pump and Tank   
THIS UNIT HAS Steel Contact Drum 9¾" diameter and
  1- additional spare "New" Rubber Coated Contact Drum.
   Spare "New " Pillar Bearing Blocks for contact drum.
Inventory Reference G3975-9651  



WET TYPE
GRINDER WIDE BELT & DEBURRING BRUSH FINISHER
▼
37" AEM - TIMESAVER ABRASIVE BELT GRINDER & DEBURRING FINISHER
Two Heads: Wide Belt & Brush Drum        Heavy Duty        Model 402-37 HDCMW
1st Head, Contact Wide Belt  20 hp.
2nd Head, Contact Brush Drum 7½ hp.
Equipped with:
    Operator Control Station
    Drive Motors per cent load meter.
    Coolant and Tank with Filter Media
    Air Knife Dryer Blower to remove coolant.
    Bed Feed System, conveyor type, variable feed.
Inventory Reference G3975-9744



DRY TYPE
▼
24" JET WIDE BELT SANDER   Model JWB 25P
Single Belt  Working width 24 inch
Combo Sanding Head
Feed Belt: Infinitely Variable Speed
Manual and Power Elevation on Feed Bed with Digital Read-Out
Drive Motor on Belt 15 hp
Inventory Reference S0403-9615 
Front to right side view        Infeed side with door open showing dust shoot & air tracking
Close-up Pro-Scale & DRO.      DRO           View Combo Sanding Head
Outfeed end view door open        Outfeed end door closed
Right side view door open



DRY TYPE
▼
36" BURLINGTON Rand Bright RECIPROCATING BED ABRASIVE BELT GRINDER
Wide Belt,   Heavy Duty
Model S36X75R          Date Mfg. 11-1998
36" wide Sanding Belt
Reciprocating Bed overall size24" x 45"
Belt Motor Drive 30 hp
Equipped with: Manual and Automatic Operation.
    Automatic Reciprocating Bed movement, Longitudinally and Up Feed
    Bed Positioning DRO.   Pneumatic Fixture Clamping
    Drive Motor per cent load meter
Inventory Reference G3975-9650 
Front view.     Part Holding Fixture.    Front to right side view.
Close-up Bed Height DRO.       Rear view.
View inside drum and belt cabinet.    Left side view






FOR ALL YOUR EQUIPMENT REQUIREMENTS: Wanted or For-Sale
        Please Call  1- 213-627-2847
        Fax  1- 213-627-2499
        E-mail us at   sales@centurymachinery.com

ENGLISH WHEEL FORMING MACHINE S5160-

"NEW" ENGLISH WHEEL In-Stock
▼ 

NEW”  SHAPE IT ENGLISH WHEEL FORMING MACHINE
Model EW52
Throat Depth 52"
Distance Upper and Lower Casting 63"
OPENING: Between rolls will vary depending on
       diameter of Top & Bottom Forming Rolls 18¾"
Top Forming Roll Width x Diameter 9" x 3½"
Bottom Anvil Wheel Holder Adjusts Up/Down and has Quick Release
WITH:
      (6) Lower Anvil Wheels various radius.
      (1) Anvil Wheel Oak Storage Rack
Inventory Reference S5160-9655     




NEW PLANISHING HAMMER  24" thru 36" Throat


FOR ALL YOUR EQUIPMENT REQUIREMENTS: Wanted or For-Sale
    Please Call  1- 213-627-2847
    Fax  1- 213-627-2499
    E-mail us at    sales@centurymachinery.com

STRUT GRINDER CNC, Butler Newall   G7930
 CYLINDRICAL GRINDER,GAP BED   G4790-

PLEASE NOTE: Strut Grinder has a hold on it at this time and is not
     available for sale at this time.  Email us a request for future need.

110" swing x 96" centers BUTLER NEWALL CNC GAP BED STRUT CYLINDRICAL GRINDER
                              Mfg. 1986     FANUC Series Oi-MA retrofitted 2002
             Condition: In running order, prior to being taken out of service January 2008,
             Appears to be in Excellent Mechanical Condition.
CAPACITY
      Swing over Table 26" Diameter
      Swing in Gap 110" Diameter
      Distance between Centers: Gap Open 96"
      Grinding Stroke 70"
GRINDING WHEELHEAD:  Spindle Speed, Variable
GRINDING WHEEL (diameter, face and hole) 30" x 3" x 12"
WHEELHEAD CARRIAGE TRAVERSE: Grinding Rate, INFINITE
HEADSTOCK: Live and Dead Center
      Headstock Pedestal has Swivel Base, Angles Towards and Away from Wheelhead.
      Headstock and Footstock center taper  No. 16 Jarno
      Number of work rotation speeds., Infinite thru 2-speed ranges.
TRAVERSE: Feed (Minimum) .022" Rev., Rapid (Maximum) 1.14"/Rev.
CNC CONTROLS, FANUC Series Oi-MA retrofitted 2002
     GE Adjustable Speed Drive.   Leeson Wheel Inverter.
     McLean Midwest Control Air Conditioner.
     Sony DRO to read taper angle on swivel bed.
     Sony 3-axis DRO Measuring System.
EQUIPPED WITH: (1) Internal Spindle Attachment.    (1) Grinding Wheel Hub          
     Radius Stone Dresser    (2) Part Steady Rests      (2) Part Stages.
     (2) Live Centers.      (2) Dead Centers.     (1) Wheel Balancer Arbor.
     (1) Polycoln Liquid Filtration Coolant Recovery System, with Slug Conveyor, Model W85-400D6
     Work Area Enclosure      (1) Steel Operator Work Stage
Inventory Reference G7930-9688     Over-all view.        Fanuc Controls

PRESS, ELECTROSHAPE FLUID FORMING P4740-

CINCINNATI ELECTROSHAPE FLUID FORMING PRESS    Model 150-6448
    Down Acting    Hydraulic Power
    Capacity clamping 150 tons
    Useful Die Area 64" x 48"
    Distance between 4-posts 50" x 50"
    Stroke Ram 36"
    Shut Height:42" Open and Closed 12"
    Bed Height above floor 42"
    Produces 150 Kilojoules or 109,000 Foot Pounds of Energy with Up to 100 Tons Clamping Pressure
*THIS IS A DOWN ACTING FOUR POST HYDRAULIC PRESS*
Inventory Reference P4740-8910
Photo Front view.    Photo close-up T-Slotted Bed.
Photo Hydraulic Pump.    Photo taken with-in our warehouse. 
Description Forming Process.    Book Photo of press 

PRESSES, FLUID FORMING, BLADDER   P5206-

        "Direct Acting,  Flex-Die and  Rubber Pad Presses"

PLEASE NOTE  "Large Forming Area on Verson Wheelon 60000R-50x240"

VERSON WHEELON FLUID FORMING PRESS   Model 60000R-50x240
    Capacity 60,000 Tons
    Two  50" x 240" Trays
    Tray Depth 6" and 10"
    Forming Pressure10,000 psi
    High Pressure Accumulator
Equipped with 2- Throw Pad Roll-Up Devices, Hydraulic Driven.
        1- Extra Fluid Cell
        1- Pad
"From Major US Aircraft Manufacturer   Very Low Usage"
Inventory Reference P5206-7106 
  2- Photo's within Right and Left Front View
  3- Photo's within Front Controls Station, Rear View and Side View




SALE PENDING on this item.  Please contact us to be placed onto our
  our active Wanted List.  sales@centurymachinery.com
▼▼
VERSON WHEELON FLUID FORMING PRESS   Model 41000R-50x168
    Capacity 41,000 Tons
    Two 50" x 168" Trays
    Forming Depth 6 and 10"
    Forming Pressure 10,000 psi
Equipped with: 2-Tray Fill Plates
        2- Throw Pad Roll Up Devices  Hydraulic Driven
        2- Electric Hoists
        Fluid Cell Removal Unit  and Loaded with Spare Parts
        (Third Table and Tray is available with this press)
Inventory Reference P5206-15923  

PRESSES, HYDROFORM    P5206-

THIS ITEM HAS BEEN SOLD, Please contact us to be placed onto our
  our active Wanted List.  sales@centurymachinery.com
26-15-12 CINCINNATI HYDROFORM PRESS   Round Chamber
    26" Blank Diameter
    15,000 psi Forming Pressure
    12" Forming (Draw) Depth
 Right Side to Front View.   Left Side to Front View     Left Side View
Rear View     Inventory Reference P5206-19381  




25-10-12 CINCINNATI HYDROFORM PRESS  Round Chamber
        25" Blank Diameter
        10,000 psi Forming Pressure
        12" Forming (Draw) Depth
Equipped with: Rear Tool Shuttle Table
        Side Tool Shuttle Table
 This photo Left Side View with Side and Rear Shuttle Tables
 This photo Close Up of Shuttle Table and Extra Tooling
 This photo Rear View Forward.  This photo close up Controls 
Inventory Reference P5206-18872   

PROFILERS AND ROUTING MILLS: click here

FOR ALL YOUR EQUIPMENT REQUIREMENTS: Wanted or For-Sale
    Please Call: 1- 213-627-2847
    Fax: 1- 213-627-2499
    E-mail us at:    sales@centurymachinery.com

RIVETER AND DRILL   R3998-

C-Frame PNEUMATIC RIVETERS AVAILABLE  Chicago Pneumatic

Please Call: 1- 213-627-2847
Fax:    1- 213-627-2499
E-mail us at:  sales@centurymachinery.com

ROLLS, AIRCRAFT, Farnham     R4700-

PLEASE NOTE: WE ARE IN NEED of  FARNHAM ROLLS 10 foot, 15 foot and 20 foot length.
         If you know of any for-sale please contact us at TEL. 1-213-627-2847 or
                                 Email us at sales@centurymachinery.com

ROUTERS, Pin and Radial Type click here 

THE FOLLOWING are examples of what is in stock (Pin Routers and Inverted Routers.)
          To view more, Click on link or go to Router Section.
         ▼     ▼     ▼

ONSRUD PIN ROUTER, Model A1136
    36" throat
    Spindle Speeds 10,000 and 20,000 rpm
    Spindle Drive 7½ hp. and 10 hp
    Spindle travel by pneumatic cylinder Up and Down
    Table Size 26" x 36"               Inventory Reference   R8903-8701   


ONSRUD PIN ROUTER  Model A1136-7M
    36" throat
   Spindle Speeds 10,000 and 20,000 rpm
   Spindle Drive 7½ hp and 10 hp
   Tilting Table 36" x 48"
Inventory Reference R8903-7216
Two photo's with-in   This unit just Sold use as example of finished product





C.R. ONSRUD INVERTED SPINDLE ROUTERS
C.R. ONSRUD VERTICAL ROUTER  Model 00210   Mfg.  2001
Table Size 28.5" x 43.5"
Variable Spindle Speeds 12,000 thru 21,000 rpm.
Spindle Drive Motor 10 hp
Collet Capacity thru 3/4"
CONDITION Like New
Equipped with 1/4",  3/8", 1/2", and 3/4" Collets and Collet Nuts.
    (18) Off-set Guides Insets.   (1) Extra Table Open Insert.
Inventory Reference S3053-9647 
Front view.    Right side view.      View Spindle and controls.
 Close up Operator Control Panel.    Right side to Rear View Spray Mist Lube.
 Motor access door open.    Close up drive motor.
  Close Up Safety Shield - Mist Lube.



THE FOLLOWING are examples of what is in stock (Pin Routers and Inverted Routers.)
          To view more, Click on link or go to Router Section.
          ▼     ▼     ▼

ORTON  INVERTED SPINDLE Tilting Spindle SHAPERS and ROUTERS (Re-Built)   R8903-     S3053-
▼    ▼    ▼     ▼

 

ORTON INVERTED SPINDLE SHAPER ROUTER   Model E   Tilting Spindle
Spindle Tilts thru 45 degrees.
Table Size 40" x 60"
Spindle Speed 10,000 rpm     Spindle drive 5 hp
Inventory Reference S3053-16608   




THESE SHAPERS REBUILT FOR:
Inventory Reference 6609 ORTON Tilting Spindle SHAPER ROUTER
                   Re-built for Lockheed.    
Inventory Reference 6748 ORTON Tilting Spindle SHAPER ROUTER
                   Re-built for Boeing  

      ORTON INVERTED SPINDLE SHAPER ROUTER     Model F    Tilting Spindle
                                                 REBUILT 2007
                                         "LOADED WITH EVERY OPTION"
       *Variable Spindle Speed thru 10,000 rpm                 *Power Spindle Tilting
       *Power Part Feeder                                         *Operator Vacuum Part Holder
       *Digital Spindle Degree Indicator               *DC Spindle Motor Brake
       *Table Size 30" x 60"                                 *Collet Type Tool Holder 1" Capacity
       *Additional feature Over-arm Spindle Bearing Support for Arbor spindle
       *Micro-mist Spindle Bearing Lube System
       New Cost $59,750.00                                 Our Rebuilt Price $19,750.00
                        Inventory Reference S3053-18414         Front View       Rear View
                      New Solid State Spindle Speed Control

TWO IN-STOCK
▼▼
ORTON  Inverted Tilting Spindle SHAPER ROUTER     Model F   
      Spindle Speed thru 10,000 rpm
      Spindle Tilts from 90 degrees, and unit adjusts 45 degrees Under to 30 degrees Outward.
      Collet Type Tool Holder 1" Capacity
      Table Size 30" x 60"
      Offset Guide Pin adjust up and down
Equipped with   Power Spindle Tilting   -   Power Part Feeder
Operator Vacuum Part Holder   -     Digital Spindle Degree Indicator 
DC Spindle Motor Brake     -      Micro-mist Spindle Bearing Lube System
Over-arm Spindle Bearing Support for Arbor spindle
Inventory Reference S3053-5360        
Inventory Reference S3053-5703 
Please see above Orton F in box for finish.


THREE IN-STOCK
▼▼▼
ORTON  Inverted Tilting Spindle SHAPER ROUTER    Model F
    Spindle Speed 10,000 rpm.
    Spindle Tilts from 90 degrees, and unit adjusts 45 degrees Under to 30 degrees Outward.
    Spindle Drive Motor 7½
    Collet Type Tool Holder 1" Capacity
    Table Size 30" x 60⅝"
    Offset Guide Pin adjust up and down
    Vertical Height Adjustment and Tilting Manually
Inventory Reference S3053-6661   
Inventory Reference S3053-6682   
Inventory Reference S3053-8714     This unit Rebuilt