ROLLS "All Type"

Link back to Home Page: www.centurymachinery.com

POINT and CLICK CATEGORIES or JUST SCROLL DOWN, CATEGORIES ARE IN ALPHABETICAL ORDER.  ▬▬▬▬▬▬►

*ROLLS, ANGLE BENDING, Horizontal & Vertical*
*ROLLS, BENDING, AIRCRAFT*
ROLL FORMERS▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬►PLEASE USE THIS SCROLL BAR to get section▬▬▬▬▬►►►►►►
*ROLLS, PLATE BENDING, Initial Type*
*ROLLS, BENDING: "New"*
*ROLLS, PLATE BENDING, Pyramid Type*

SPECIAL 78 year in business discounted price on all items listed below "CALL".


If you require a Quote Sheet PLEASE  send  us your requirements:
CENTURY MACHINERY COMPANY INC.
1937 South Santa Fe Avenue
Los Angeles, California 90021

Email: sales@centurymachinery.com
Website: www.centurymachinery.com
Telephone 1-213-627-2847
Fax 1-213-627-2499



ROLLS, ANGLE BENDING, Horizontal & Vertical





ROLLS, BENDING, AIRCRAFT   R4700-

FARNHAN FORMING ROLL
Model 2015-EX
Capacity:
    Forming Length Over-all 20 feet  (240”) (6096mm)
    Maximum Forming Thickness 0.090" (2.286mm)
    Minimum Radius 0.62" (15.748mm)
Power Elevation on both End of Top Roll
Inventory Reference R4510-10082   CLICK HERE FOR QUOTATION FARNHAM FORMING ROLL_Model 2015-EX_capacity -overall length of rolls 20 feet-240” - 6096mm_material thickness 0.090” - 2.286mm_material minimum radius 0.62” - 15.748mm_roll diameters top roll 1” - 25.4mm_bottom rolls 1-11/16” - 42.8549mm_top roll lift or elevation motor are geared motor to screw located on each end_each elevation screw with mechanical counter for top roll_each elevation motor with mechanical brake_bottom rolls each with in and out adjustment and indicators located on both end_tie rod bed adjustment to put slight bow in bed_all motors wired 440 volts - 3 phase_rolls driven by 2-speed motor 5 & 2 H.P._top elevation motors each 3 H.P_controls - roll drive motor start - stop buttons_two roll speed in forward - one roll speed in reverse_top roll up – down buttons to adjust each end of rolls at the same time_safety stop line located on front and rear_Serial Number 3-51-1
"PHOTO WILL BE POST SOON"






▼THIS ROLL HAS BEEN LEASE OUT
FARNHAN FORMING ROLL
 Model 1262-E
 Capacity:
     Forming Length Over-all 12 feet
     Maximum Forming Thickness 0.63"
     Minimum Radius 0.62"
 Power Elevation on both End of Top Roll
Inventory Reference R4510-19954  CLICK HERE FOR QUOTATION farnham forming roll_overall roll length 12 feet_model 1262-E_minimum radius 0.62 inch_thickness 0.63 inch_top roll 1 inch diameter_bottom rolls 1.6875 inch diameter_equipped with power elevation both ends of top roll_tie rod adjustment to put slight bow in bed_2 speed roll motor drive_roll elevation both ends at one time or seperate_Serial Number 7-43-16
CLICK HERE FOR PHOTO farnham forming roll_model 1262-E_capacity 12 feet forming length_radius 0.62 inch_thickness 0.63 inch_motorized roll adjustment on each end_Serial Number 7-42-16_Left End to Front view Photo Left End to Front view.
CLICK HERE FOR PHOTO farnham forming roll_model 1262-E_capacity 12 feet forming length_radius 0.62 inch_thickness 0.63 inch_motorized roll adjustment on each end_Serial Number 7-42-16_Right End to Front view Photo Right End to Front view.    CLICK HERE FOR PHOTO farnham forming roll_model 1262-E_capacity 12 feet forming length_radius 0.62 inch_thickness 0.63 inch_motorized roll adjustment on each end_Serial Number 7-42-12_Close-up Operator Controls Photo Close-up Operator Controls.




PLEASE NOTE: WE ARE IN NEED of  FARNHAM ROLLS 10 foot, 15 foot and 20 foot length.
         If you know of any for-sale please contact us at TEL. 1-213-627-2847 or
                                 Email us at sales@centurymachinery.com


 

ROLL FORMING LINE (Roll Formers)    R5610-

DAHLSTROM ROLL FORMING LINE with STRAIGHTENER & 4-Post CUT-OFF PRESS
     Former Model 360-7,      Cut Off Press Model 2D
SPECIFICATIONS:
NUMBER OF STANDS 7
CAPACITY:
   Material Thickness 0.035"
   Spindle Roll Shaft Diameter 1½"
   Roll Space 8"
   Horizontal Centers 8"
   Adjustment 4" - 5"
LINE SPEED: Infinitely Variable  50 thru 150 FPM
EQUIPPED WITH:
   Each Stand has two Rolls for a total of:
       7-sets FORMING ROLLS plus STRAIGHTENING & LEVELING ROLLS
   STRAIGHTENING ROLLS 3-Adjustable Top Rolls & 4-set Bottom Rolls with 1-set End Rolls.
   DAHLSTROM 4-POST CUT-OFF PRESS Model 2D, Capacity 8 Tons, Stroke 2",
          Shut Height Adjustable 4" - 6", Die Area 9", Flywheel 300 rpm, Air Clutch, Air Brake,
          Controls: Start/Stop Buttons, Run/Auto Switch, On Light, Forward/Reverse Switch.
          Motor Drive 2 H.P, 230/460 volts.
Inventory Reference R4496-10033  CLICK HERE FOR QUOTATION dahlstrom roll former with straightener and dahlstrom four post cut off_forming roll model 360-7_stations 7_spindle shaft diameter 1.5 inch_roll space 8 inch_roll range 4 inch - 5 inch_horizontal centers 8 inch_material thickness capacity 0.035 inch_roll line speed infinitely variable 50 thru 150 fpm_material straghtening rolls & dahlstron four post cut-off_model 2DP_ capacity 8-tons_air clutch air brake_Serial Number Forming Rolls 614_Serial Number Cut Off Press P480



DAHLSTROM ROLL FORMING LINE with STRAIGHTENER & 4-Post CUT-OFF PRESS
     Former Model 360-10-OB,      Cut Off Press Model 8TP
SPECIFICATIONS:
NUMBER OF STANDS 10
CAPACITY:
   Spindle Roll Shaft Diameter 1½"
   Roll Space 8"
   Horizontal Centers 8"
   Adjustment 4" - 5"
LINE SPEED: Infinitely Variable  50 thru 150 FPM
EQUIPPED WITH:
   Each Stand has two Rolls for a total of:
       10-sets FORMING ROLLS plus STRAIGHTENING & LEVELING ROLLS
   STRAIGHTENING ROLLS 3-Adjustable Top Rolls & 4-set Bottom Rolls with 1-set End Rolls.
   DAHLSTROM 4-POST CUT-OFF PRESS Model 8-TP, Capacity 8 Tons, Stroke 2",
          Shut Height Adjustable 4" - 6", Die Area 9", Flywheel 300 rpm, Air Clutch, Air Brake,
          Controls: Start/Stop Buttons, Run/Auto Switch, On Light, Forward/Reverse Switch.
          Motor Drive 2 H.P, 230/460 volts.
Inventory Reference R4496-10032  CLICK HERE FOR QUOTATION dahlstrom roll former with straightener and dahlstrom four post cut off_model 360-10-OB_stations 10_spindle shaft diameter 1.5 inch_roll space 8 inch_roll range 4 inch - 5 inch_horizontal centers 8 inch_roll line speed infinitely variable 50 thru 150 fpm_material straghtener & dahlstron four post cut-off_model 8TP_ capacity 8-tons_air clutch air brake_Serial Number Former P661



 

ROLL, PLATE BENDING, Initial Type   R5603-


ROPER WHITNEY INITIAL PINCH POWER SLIP BENDING ROLL
Model 3418
Capacity Mild Steel  16-18 gauge x 48" wide
Diameter Rolls 3"
All Rolls driven
Equipped with
3-Rod Forming Grooves 1/4", 1/2", 5/8"
Motor dive 1 hp.
 Inventory Reference R5603-9738 CLICK HERE FOR QUOTATION roper whitney initial pinch slip bending rolls_capacity 48 inch wide x 16-18 gauge mild steel_model 3418_diameter rolls 3 inch_3 wire grooves_mounted on stand_Serial Number 151-10-77



ROPER WHITNEY INITIAL PINCH POWER SLIP BENDING ROLL
Model 3418
Capacity Mild Steel  13 gauge x 50" wide
Diameter Rolls 4"
All Rolls driven
Equipped with
3-Rod Forming Grooves 3/8", 5/16", 1/2"
Motor dive 1 hp.
Inventory Reference R5603-10071



WEBB INITIAL PINCH POWER SLIP BENDING ROLL
Model 2L
Capacity Mild Steel  22 gauge x 120"wide
Diameter Rolls 5.2"
All Rolls gear driven
Equipped with
  Manual Rise and Fall on Rear and Bottom Roll
  3-Longitudinal starting grooves on rear roll
  Roll Forward and Reverse Switch
 Inventory Reference R5603-9869  CLICK HERE FOR QUOTATION webb initial pinch bending roll_model 2L_capacity 10 feet length x 22 gauge_10-2X22_manual elevation_3-longitudinal grooves in rear roll_Serial Number 4946
 CLICK HERE FOR PHOTO webb initial pinch bending roll_model 2L_capacity 10 feet length x 22 gauge_10-2X22_manual elevation_3-longitudinal grooves in rear roll_Serial Number 4946_Left End to Front view Photo Left End to Front View.    CLICK HERE FOR PHOTO webb initial pinch bending roll_model 2L_capacity 10 feet length x 22 gauge_10-2X22_manual elevation_3-longitudinal grooves in rear roll_Serial Number 4946_Right End to Front view Photo Right End to Front View.


 

"NEW" JET SLIP HAND ROLLS    5-Models Available
             22 gauge x 12"    24 gauge x 18"     20 gauge x 24"     22 gauge x 36"     16 gauge x 50"
    "Photo and Specification are with-in Camera.  jet hand powered slip roll_22 gauge x 12 inch wide_ 24 gauge x 18 inch wide_20 gauge x 24 inch wide_22 gauge x 36 inch wide_16 gauge x 50 inch wide Photo




ROLLS, PLATE BENDING, Pyramid Type   R5610-






PLEASE CONTACT US FOR FULL Quotations and Photo's

Phone  1-213-627-2847    Fax  1-213-627-2499  or
E-Mail  sales@centurymachinery.com
" THANK YOU for taking the time to visit our site "